I have pelo adverse vacuum performance change with the catch can in place. It just catches any oil. I still smell oil vapor when the pump first starts up, but not nearly as much. I've only emptied the can once or twice since I've had it installed. I slightly over filled the pump and it blew out into the can, then ran it with the FDer valve open for a few minutes. Nothing got past the can. I used the outside port as IN and the middle one as out. I did take the port off and the longer one should be the inlet port. It's not a great deal longer. Tony Edited January 22, 2016 by TonyC updated (log)
Harvest Right has created the world’s first high quality, affordable Home Freeze Dryer. It is less than one quarter the cost of comparable freeze drying systems, and is easier to use than a microwave.
The current and emerging food crisis in the United States has millions of Americans very concerned about the future. From supply chain shenanigans to food processing plants “inexplicably” being compromised to bird flu decimating the poultry industry, it’s no wonder there has been a sharp rise in the “prepper” food industry.
The best place to buy a freeze dryer is directly from the manufacturer’s website. That way, a warranty will be included, there’s a guarantee the machine wasn’t tampered with by anyone (even by accident), and buyers can get additional information from customer service.
The pros and cons are easy to understand. In fact, there really is only one pro and it’s a huge one. Those who are willing to spend the time and money to freeze dry their own food should do so as long as they’re going to be committed.
It's awesome! I don't have a freeze dryer yet but am planning to place an order tomorrow. I am super curious how Kerry's scroll pump is holding up... eliminating the oil from the equation would make this whole thing SO much easier.
1) I installed a 3/4" wide high density closed cell foam in the gap between the front of the chamber and the back of the front panel - just what Harvest Right suggested except all the way around (the first picture shows the gap). Use your fingers to push it into place. It needs to be tight against the inside panel. I then installed a vapor barrier around the entire FDer chamber. I used 7mil plastic and clear packing tape.
I'm actually working now on making myself a vacuum microwave Buy Now instead. Got the idea from an article in MacLeans magazine about Domenic and Cindy Duby, who use one to produce interesting flavours. Takes up less space and hopefully produces a product a bit faster. We'll see how it works out.
The evaporator coils that touch the surface of the stainless steel vacuum chamber reach about -42 F. With food in the chamber and because the location of the thermister is on the middle shelf of the four shelves, the temperature it records is going to range from -25 to -30 F in the 9 hour default freeze time. This temperature is very adequate for freeze drying the food.
Over night the FDer warmed up and the next morning we had a massive puddle under it - running off the counter onto the floor. I cleaned up the mess, but the next day the puddle was even bigger. On the 3rd day it was back again just as large even though I left a large towel under the FDer.
This type of website can’t hurt when buying something minor, like a piece of clothing, but it’d be smart to steer clear from them when buying expensive equipment.
There are 3 ports on the chamber that I made slits in the plastic to get around and taped them up once around them. Do not tape to the insulation. Tape only to the vapor barrier plastic. It doesn't take long, just be careful. After the plastic is in place and secure around the chamber I sealed the plastic to the back of the front and back panels using the packing tape. All the way around the front and back of the chamber to completely seal the chamber from outside air and humidity.
I am looking for a more defined "heuristic" curve based upon the internal temperature. I am sure that your engineers probably have tables for such things. I also know that different foods freeze at different rates, that is why I am asking for a heuristic answer.
12 Posted September 16, 2015 You've given me an idea. I have the parts at the shop to use an actual filter head and a spin on filter. I could have a bracket laser cut and powder-coated that would hold the filter/head assembly horizontal which would allow it to completely drain and the outside of the filter would stay clean.